• Shuffle
    Toggle On
    Toggle Off
  • Alphabetize
    Toggle On
    Toggle Off
  • Front First
    Toggle On
    Toggle Off
  • Both Sides
    Toggle On
    Toggle Off
Front

How to study your flashcards.

Right/Left arrow keys: Navigate between flashcards.right arrow keyleft arrow key

Up/Down arrow keys: Flip the card between the front and back.down keyup key

H key: Show hint (3rd side).h key

image

PLAY BUTTON

image

PLAY BUTTON

image

Progress

1/60

Click to flip

Card Range To Study

through

60 Cards in this Set

  • Front
  • Back
A SOFT-FACED HAMMER IS KNOWN BY WHAT NAME?
MALLET.
WHEN RIVETS ARE TOO LONG FOR REPAIR,YOU CAN SIZE THEM TO THE CORRECT LENGTH WITH WHAT TOOL?
ROTARY RIVET CUTTER.
WHAT MUST YOU USE TO FORM A BUCTAIL ON A CORRECT RIVET?
BUCKING BAR.
LOCALLY MANUFACTURED BUCKING BARS ARE NORMALLY MADE FROM WHAT TYPE OF STEEL?
TOOL STEEL.
TO TRANSFER HOLE LOCATIONS FROM THE AIRFRAME OR SKIN TO A PATCH, YOU SHOULD USE WHAT TOOL?
HOLE FINDER.
WHAT IS THE COLOR OF A 1/8 INCH CLECO FASTENER?
COPPER.
WHAT IS THE DIFFERENCE BETWEEN SNIPS AND SHEARS?
NORMALLY, SHEARS ARE USED TO CUT HEAVIER GAUGE METAL.
WHAT ARE THE FIVE TYPES OF PNEUMATIC RIVETERS?
ONE-SHOT GUN, FAST-HITTING GUN, SLOW-HITTING GUN, CORNER GUN, AND SQUEEZE RIVETER.
WHAT RIVET GUN IS GENERALLY USED FOR HEAVY HITTING,AND UNDER SUITABLE CONDITIONS , IS THE FASTEST METHOD OF RIVETING?
ONE-SHOT GUN.
WHAT WILL HAPPEN IF YOU APPLY TOO MUCH PRESSURE TO THE DRILL?
IT CAN CAUSE THE DRILL TO SIDE SLIP AND THE HOLE TO BE ELONGATED.
MOST PNEUMATIC DRILLS ARE POWERED BY WHAT TYPE OF MOTOR?
VANE AIR.
A FEXIBLE SHAFT DRILL IS ALSO KNOWN BY WHAT OTHER NAME?
SNAKE DRILL.
THE COMBINATION OF BENDING AND STRETCHING OF METAL,USING MALE AND FEMALE DIES, FORMS WHAT TYPE OF COUNTERSINK?
DIMPLE.
WHY IS IT NECESSARY TO USE A HOT DIMPLING PROCESS FOR ALUMINUM ALLOYS?
ALUMINUM ALLOYS ARE SUBJECT TO CRACKING WHEN FORMED.
PORTABLE POWER-OPERATED SNIPS ARE MORE COMMONLY REFERRED TO BY WHAT NAME?
UNISHEARS.
WHAT SHEET METAL EQUIPMENT WOULD YOU USE TO FABRICATE A WIRE EDGE?
BAR FOLDER.
WHAT BRAKE HAS REMOVABLE STEEL FINGERS OF VARYING WIDTHS?
BOX AND PAN BRAKE.
WHAT IS THE MOST COMMONLY USED LAYOUT FLUID?
BLUING FLUID.
WHAT IS THE ONLY THING YOU SHOULD USE A SCRIBER FOR WHEN LAYING OUT ALUMINUM OR MAGNESIUM?
TO INDICATE WHERE THE METAL IS TO BE CUT OR DRILLED.
THE AMOUNT OF MATERIAL CONSUMED IN THE BENDING PROCESS IS KNOWN BY WHAT TERM?
BEND ALLOWANCE.
WHAT IS THE OUTSIDE DIMENSION OF THE FORMED PART CALLED?
BASE MEASUREMENT.
THE SETBACK IS THE COMBINATION OF THE METAL THICKNESS AND WHAT OTHER FACTOR?
RADIUS.
MACHINES USED TO CUT SHEET METAL ARE CLASSIFIED INTO WHAT TWO GROUPS?
POWER AND MANUAL OPERATED.
WHEN USING A VISE AND FORMING BLOCKS TO MANUALLY FORM A PART,WHAT ARE THE THREE MATERIALS THAT THE MALLET YOU USE MUST BE MADE FROM?
RUBBER, PLASTIC, OR RAWHIDE.
WHEN YOU CUT SHEET METAL, HOW MUCH SHOULD YOU ADD TO ALLOW FOR TRIM?
1/4 IN.
BEFORE MAKING ANY BENDS ON THE LAYOUT, WHAT SHOULD YOU DO TO MAKE SURE THE BRAKE SETTINGS ARE RIGHT?
USE A PIECE OF SCRAPE METAL.
HOW MANY ADJUSTMENTS MUST BE CHECKED ON THE BAR FOLDER BEFORE YOU CAN PROPERLY BEND AND FOLD METAL?
TWO.
TO FORM CYLINDRICAL OR CONICAL SHAPES,YOU SHOULD WHAT MACHINE?
SLIP-ROLL FORMING MACHINE.
WHAT MACHINE SHOULD YOU USE TO MAKE A GROOVE ON A BUCKET?
BEADING ROLLS.
WHAT DERTEMINES THE MINIMUM RIVET DIAMETER?
THE THICKNESS OF THE METAL BEING RIVETED.
WHAT IS THE NAVY STANDARD COUNTERSINK ANGLE?
100o.
A CP350 BLIND RIVET TOOL IS USED TO PULL WHAT TYPE OF RIVET?
HUCH RIVET.
WHEN DRILLING OUT A SELF-PLUGGING RIVET,WHAT SIZE DRILL BIT WOULD YOU USE TO DRILL A 1/8-INCH RIVET?
No. 31 DRILL BIT.
AFTER CLEANING THE DAMAGED AREA OF AN AIRCRAFT, WHAT IS THE NEXT STEP IN THE REPAIR PROCESS?
INSPECT FOR SECONDARY DAMAGE.
WHAT KIND OF DAMAGE CAN TURN INTO PERMANENT DAMAGE IF NOT PROPELY TREATED?
CORROSION DAMAGE.
DAMAGE CAUSED BY TOOLS, BOLTS, RIVETS, AND NUTS LEFT ADRIFT IS KNOWN AS WHAT TYPE OF DAMAGE?
FOREIGN OBJECT DAMAGE.
WHAT TYPE OF DAMAGE CAN BE IDENTIFIED BY LOOSENED, SHEARED,OR POPPED RIVETS?
STRESS.
WHEN INSPECTING AN AREA FOR DAMAGE, YOU SHOULD ALWAYS CHECK RIVET AND BOLT HOLES FOR WHAT CONDITION?
ELONGATION.
WHAT TYPE OF TEST SHOULD ALWAYS BE PERFORMED ON METAL AFTER A FIRE HAS OCCURRED?
HARDNESS TEST.
IF YOU SUSPECT A CRACK EXIST, WHAT TYPE OF INSPECTION SHOULD YOU PERFORM?
NONDESTRUCTIVE INSPECTION.
SMALL CRACKS THAT CAN BE STOP-DRILLED, DENTS, SCRATCHES, OR OTHER MINOR DAMAGE THAT DOES NOT REQUIRE MAJOR REPAIR OR REPLACEMENT AND DOES NOT RECTRICT FLIGHT STATUS IS DEFINED AS WHAT TYPE OF DAMAGE?
NEGLIGIBLE DAMAGE.
DAMAGE THAT CANNOT BE REPAIRED BY ANY PRACTICAL MEANS IS DEFINED AS WHAT TYPE OF DAMAGE?
DAMAGE REQUIRING REPLACEMENT.
THE MAJOR REQUIREMENT ON MAKING A REPAIR IS TO ENSURE YOU DUPLICATE WHAT CONDITION?
STRENGTH OF THE ORIGINAL PART OR STRUCTURE.
THE PROCESS OF INTERPRETING AND TRANSCRIBING OF INFORMATION FROM BLUEPRINTS, DRAWINGS, AND WRITTEN INFORMATIONS FOR THE METAL TO BE MADE INTO A/C PARTS IS KNOWN BY WHAT TERM?
LAYOUT.
IF YOU ARE REQUIRED TO FABRICATE MULTIPLE PARTS OF THE SAME DIMENSIONS, WHAT CAN YOU USE TO ENSURE A HIHGER DEGREE OF UNIFORMITY AND SPEED PRODUCTION?
A TEMPLATE.
WHAT SHOULD YOU USE TO MAINTAIN AERODYNAMIC SMOOTHNESS WHEN REPAIRING NEGLIGIBLE DAMAGE, STEPS, AND GAPS?
AERODYNAMIC FILLER.
WHAT STEP MUST YOU TAKE BEFORE APPLYING A LAP PATCH OVER A CRACK?
STOP-DRILL BOTH ENDS OF THE CRACK.
AS A GENERAL RULE, WHEN YOU MAKE A FLUSH PATCH,WHAT IS THE MAXIMUM CLEARANCE BETWEEN THE SKIN AND THE FILLER?
1/32 IN.
WHEN MAKING A REPAIR OVER AN INTERNAL STRUCTURE, WHAT RIVET PATTERN MUST YOU USE?
THE EXISTING RIVET PATTERN.
THE MAIN SPANWISE MEMBERS DESIGNED PRIMARILY TO TAKE BENDING LOADS ON THE WING OR OTHER AIRFOILS ARE KNOWN AS WHAT TYPE OF MEMBERS?
SPARS.
WHAT STRUCTURAL MEMBERS ARE DESIGNED THE AIRFOIL SHAPE AND RIGIDITY?
RIBS.
WHAT STRUCTURAL MEMBER RUNS FORE-AND-AFT ALONG THE LENGTH OF THE FUSELAGE AND IS CONTINUOUS ACCROSS FRAMES AND BULKHEADS?
LONGERON.
THE SELF-SEALING FUEL CELL NOW IN NAVAL SERVICE ARE MADE UP WHAT OF TOTAL NUMBER OF PRIMARY LAYERS OF MATERIAL?
FOUR.
WHAT IS THE MAIN ADVANTAGE OFA BLADDER-TYPE FUEL CELL OVER A SELF-SEALING FUEL CELL?
LESS TOTAL WEIGHT.
WHEN APPLYING THE NYLON BARRIER OF A RUBBER-TYPE BLADDER FUEL CELL, YOU SHOULD USE WHAT METHOD OF APPLICATION?
BRUSH SWAB, OR SPRAY.
THE MILLED SKINS OF AN INTEGRAL FUEL CELL ARE NORMALLY FASTENED TO THE A/C BY WHAT MEANS?
BOLTS.
A FUEL LEAK THAT REAPPEARS 30 MIN AFTER IT IS WIPED DRY IS CLASSIFIED AS WHAT CATEGORY OF LEAKAGE?
SEEP.
WHAT IS THE FIRST STEP YOU SHOULD TAKE TO STOP A FUEL LEAK IN AN INTEGRAL FUEL CELL?
RETORQUE ALL FASTENERS 6 INCHES ON EITHER SIDE OF THE LEAK.
TO ALLOW THE GUN PISTON TO RETURN BEFORE ANOTHER CYCLE CAN BEGIN,THE TRIGGER OFA SEALANT INJECTOR GUN MUST BE RELEASED APPROXIMATELY HOW OFTEN?
EVERY 30 SECONDS.
WHAT GAS IS USED TO PRESSURE TEST A REPAIR MADE OF AN INTEGRAL FUEL CELL?
NITROGEN.