Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
21 Cards in this Set
- Front
- Back
Access lists are available for which of the following networking protocols?
Select one or more: A. AppleTalk B. NetBEUI C. IP D. IPX |
A. AppleTalk
B. NetBEUI D. IPX |
|
Access lists use the actions ____ or ____ traffic based on source address, destination address, protocol type, and port number of a packet.
Select one: A. allow, block B. permit, deny C. permit, block D. allow, deny |
B. permit, deny
|
|
Before modifying or adding access lists, what command should an administrator type?
Select one: A. no reload B. reset in 30 C. copy run start D. reload all |
C. copy run start
|
|
After you create access lists, what must they be applied to so they can begin filtering traffic?
Select one: A. levels B. ports C. programs D. interfaces |
D. interfaces
|
|
Which configuration mode allows an access list to be created?
Select one: A. line configuration B. global configuration C. interface configuration D. routing protocol configuration |
B. global configuration
|
|
To view all the access lists defined on a router, use the show ____ command.
Select one: A. ip interfaces list B. startup-config C. ip access-groups D. access-lists |
D. access-lists
|
|
What are the number ranges for standard IP access lists?
Select one: A. 1-99 B. 100-199 C. 0-99 D. 0-100 |
A. 1-99
|
|
To remove an access list, which of the following syntax examples represent the correct way to do this?
Select one: A. remove list [list #] B. remove access-list # C. no access-list [list #] D. no access # |
C. no access-list [list #]
|
|
Which of the following access-list commands will allow only packets from the 192.16.10.0 network?
Select one: A. Access-list 101 permit 192.16.10.0 255.255.255.0 B. IP permit 192.16.10.0 C. Access-list 1 permit 192.16.10.0 0.0.0.255 D. Access-list 1 deny 0.0.0.0 255.255.255.255 |
C. Access-list 1 permit 192.16.10.0 0.0.0.255
|
|
How many access lists per protocol can an interface have?
Select one: A. 1 inbound B. 1 standard and 1 extended C. 1 inbound and 1 outbound D. 2 inbound and 2 outbound |
C. 1 inbound and 1 outbound
|
|
To view which interfaces have IP access lists set, use the show _____ ______ command.
Select one: A. ip access-lists B. ip interface C. interface list D. access-lists |
B. ip interface
|
|
What mode must the router be in to apply an access list to a router?
Select one: A. Router configuration mode B. Interface configuration mode C. Enable mode D. Global configuration mode |
B. Interface configuration mode
|
|
Which command syntax below is used to apply an IP access list to an interface?
Select one: A. ip access-group permit 100 B. ip access-group [list #] [inout] C. show ip interface D. ip access-group [list #] [permitdeny] |
B. ip access-group [list #] [inout]
|
|
Write the wildcard mask to match all hosts in a network with a subnet mask of 255.255.255.248
|
0.0.0.7
ANSWER: 255-248 = 7 therefore the wildcard is 0.0.0.7 |
|
Access lists are not effective until they are applied to an interface.
Select one: True False |
True
|
|
In applying a standard access list, it should be located as close to the destination as possible.
Select one: True False |
True
|
|
One of the most common problems associated with access lists is a lack of planning.
Select one: True False |
True
|
|
Standard access lists permit or deny packets based only upon the destination address.
Select one: True False |
False
|
|
To remove an access list from an interface you would use the no ip access-list [list #] command.
Select one: True False |
False
|
|
Using a standard IP access list, you can filter traffic by a specific host IP, a network subnet, or a default network address.
Select one: True False |
True
|
|
Access lists are processed sequentially line by line and do not stop until a match is made.
Select one: True False |
True
|