Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
32 Cards in this Set
- Front
- Back
How are copper tubing used to restore its soft condition?
|
by anneling
|
|
What materials are most likely used for rigid lines carrying each of the types of fluids a. low pressure ventilating air b.medium pressure hydraulic fluid c.High pressure oxygen |
a. 1104-h14 or 3003-h14 aluminum alloy b.5052 aluminum alloy c.stainless steel |
|
how is the size of rigid tubing determined?
|
By the outside diameter
|
|
Indicate the outside diameter of each of these dash numbers if rigid tubing -4, -6, -12? |
-4 is 4/16 or 1/4 -6 is 6/16 or 3/8 -12 is 12/16 or 3/4 |
|
To find the diameter of rigid tubing, twice the wall thickness must be subtracted from what diameter?
|
The outside diameter
|
|
Although the use of flareless fittings eliminates flaring the tube, another operation referred to as _ is necessary prior to installation of new flareless fittings.
|
presetting
|
|
When presetting flareless fittings on 3/8 inch aluminum alloy tubing, the nut should be turned _ after the ferrule is tight against the presetting tube.
|
1 to 1/6
|
|
three characteristics of a properly preset formula on a piece of tubing? a. What around the tube end? b.Material of the tube should be raised up to atleast _ percent of the thickness of the ferrule leading edge. c.The ferrule should not be able to move _ on the tube. |
a.identification b.50 percent c.back and forth |
|
Is a rigid tube limited to uses in areas where a long straight run is possible.
|
is not
|
|
Flare angles for each type of fitting a.automotive fitting b. aviation fitting |
a.45 degree b.37 degree |
|
Soft aluminum tubing has an outside diameter of _ or smaller may be double flared?
|
3/8
|
|
Tapered pipe threads seal by _ action between the external male threads and the internal female threads.
|
wedging
|
|
The ac fitting looks a great deal like AN and MS fitting except the threads of the _ go all the way up to the flare cone.
|
AC
|
|
Color dye used to identify each type of fitting a.aluminum alloy fitings of AN and MS design b.steel fitting of AN and MS design c.AC fittings |
a.blue b.black c.gray/yellow |
|
MS flareless fittings are designed primarily for _ type of pressure hydraulic system applications.
|
high
|
|
Aluminum alloy tubing with scratches that are no deeper than _ percent of the wall thickness may be repaired?
|
10 percent
|
|
A dent of less than _ percent of the diameter of the tube is permitted, if it is not in the heel of a bend. |
20percent |
|
ALL runs of rigid tubing must have at least _ bend between th fittings to absorb strain.
|
one
|
|
A-12 rigid fuel line should be supported at least every _ inches
|
22
|
|
Color codes for fluid lines carrying these fluids? a.fuel b.lubrication c.hydraulic fluid breathing oxygen e.fire extinguishment agent |
a.red b.yellow c. Blue/yellow d.breathing oxygen e.brown |
|
Lines that are used to cary fluids that may be physically dangerous such as oxygen,nitrogen, and Freon, may be marked?
|
PHDAN
|
|
What type of flexible hose liner with phosphate ester base hydraulic fluid? |
Butyle |
|
What type of flexible hose line is compatible with nearly every liquid used? |
Teflon |
|
The size of a flexible line is determined by what diameter? |
Inside |
|
A medium pressure flexible hose has what type of outer cover. |
A smooth outer cover |
|
Material based with hydraulic fluid? Phosphate ester base hydraulic fluid? What color |
Black Green |
|
Swaged on fittings _ reusable |
Are not |
|
Medium pressure reusable fittings are made up of? |
Nipple, socket, and nut |
|
_ may be screwed into the nut of a low pressure hose fitting to hold the nipple during assembly, a special tool is not required |
Fitting |
|
Flexible fluid lines must have between percent slack between the fitting |
5 and 8 |
|
The stripe running Along the length of a flexible hose, usually containing the information needed to identify the hose, is called ? |
The lay line |
|
The lay line serves not only for identification but to indicate whether or not the line was _ when it was installed |
Twisted |