Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
70 Cards in this Set
- Front
- Back
|
WHAT COMPONENT ADJUSTS CAM CHAIN TENSION ON THE AG ENGINE DRIVE SYSTEM
|
FLOW BLOCK
|
|
|
WHAT IS THE DIAMETER OF THE CABLE FOR THE DRIVE SYSTEM
|
3/8 IN DIAMETER
|
|
|
WHAT THREE SPROCKETS MAKE UP THE DRIVE SYSTEM
|
JACK CAM DRIVE SPROCKETS
|
|
|
WHAT IS THE MAX DIMENSION FOR THE TURNBUCKLES ASSEMBLY
|
16 1/16 + 1/16 INCH
|
|
|
WHEN IS THE SIZE OF THE CRO VLAVE OPENING ADJUSTED
|
WHILE THE ENGINE IS THE BATTERY ENGINE
|
|
|
WHAT COMPONETN OF THE CRO VALVE ADJUST THE UPPER LEVER
|
LEAD SCREW
|
|
|
THE WEIGHT SELECTOR UNIT FOR THE CRO VALVE ASSEMBLY USES WHAT ELECTRICAL SOURCE
|
440 VOLTS;T 60 HERTZ 3 PHASE SOURCE
|
|
|
WHAT IS THE MAX DIFFERENCE THAT THE WEIGHT SELECTOR CAN BE OFF
|
500 +- MAX DIFF.
|
|
|
WHAT IS THE PURPOSE OF THE TRETRACT ALVE
|
HELPS RETRACT THE AG ENGINE BACK TO THE PBATTERY POSTION
|
|
|
WHAT IS THE STROKE OF THE PLUNGER ASSEMBLY FOR THE RETRACT VALVE ADJUSTED TO
|
0.678 OR 11/16 OF AN INCH
|
|
|
WHAT IS THE CORRECT TENSION FOR THE SHOCK ABSORBER ASEEMBLY ON THE RETRACT VALVE
|
50LBS
|
|
|
THE RETRACT CABLE MUST HAVE AT LEAST A MIN OF HOW MANY POUNDS OF CABLE TENSION
|
30LBS
|
|
|
WHAT IS THE DIAMETER OF THE RETRACT CABLE
|
1/4 IN IN DIAMETER
|
|
|
WHAT APROX RETRACTION TIMES ARE DESIRED FOR THE MARK 7 AG ENGINE
|
15-20 SEC
|
|
|
WHAT COMPONENT ACTS AS A SEAL BETWEEN RETRACT VALVE SEAT AND BODY
|
O-RINGS
|
|
|
WHAT COMPONENT ACTS AS A SEAL FOR THE LOWER PART THE RETRACT VALVE
|
V-RING PACKING
|
|
|
WHAT TECHNICAL MANU IS KNOWS AS THE AG BIBLE
|
NAVAIR 51-5BCA 1.1
|
|
|
WHAT IS THE CAPACTITY OF THE STOWAGE TANK FOR TH FLUID REPLENISHMENT SYTEM
|
6 GALLONS
|
|
|
WHAT IS THE PURPOSE OF THE LFUID STOWAGE SYSTEM
|
PROVIDES A METHOD FOR STORING AND TRANSFERRING ENGINE HYDRAULIC FLUID FROM ONE AG ENGINE
|
|
|
WHAT IS THE CAPACITY OF THE FLUID STOWAGE SYSTEM FOR THE MARK 7 MOD 2 AND MOD 3 ENGINGES
|
600-700 GALLONS
|
|
|
WHAT IS THE PUROSE OF THE AG FLUID COOLER
|
COOLS THE HYDRAULIC FLUID DURING OPERATION
|
|
|
THE FLUID COOLER HAS A TOTAL OF HOW MANY USHAPED TUBES
|
107
|
|
|
WHAT IS THE MAX OP HYDRAULICE TEM FOR THE MARK 7 AG
|
170F
|
|
|
WHAT COMPONENT CONNNECTS THE CROSSHEAD BODY TO THE OUTER END OF THE RAM ASSEMBLY
|
BY A SPLIT FLANGE WHICH FITS INTO A ANGULAR GROVE
|
|
|
WHAT CONNECTS THE FIXED END TO THE MEC
|
SEGMENTED CLAMPS
|
|
|
THE CROSSHEAD ASSEMBLY AND FIXED SHEAVE ASSEMBLY HAVE HOW MANY BANKS OF SHEAVE MANY SHEAVES IN EACH BANK
|
2 BANKS OF SHEAVES WITH 9 SHEAVES IN EACH BANK
|
|
|
HOW MANY ZERK FITTINGS ARE THERE ON EACH BANK OF SHEAVES FOR LUBRICATION
|
10 ON EACH BANK OF SHEAVES
|
|
|
HOW MANY SLIPPERS ARE THERE ON THE AG CROSSHEAD ASSEMBLY
|
16 TOTAL
|
|
|
WHAT IS THE PURPOSE OF THE SLIPPERS ON THE AG CROSSHEAD ASSEMBLY
|
PROVIDE A BEARING SURFACE FOR THE CROSSHEAD ASSEMBLY TO RIDE ON
|
|
|
WHAT SHEAVE MUST BE MANUALLY LUBRICATIED
|
28 IN BALL THRUST BEARING SHEAVE MUST BE MANUALLY LUBRICATED EVER 20-30 ARRESTMENTS
|
|
|
WHAT IS THE OPERATING PRESSURE FOR THE AUTOMATIC LUBE SYSTEM FOR THE MARK 7 ENGINE
|
USES SHIPS LOW PRESSURE AIR WHICH IS 80+-5 PSI PIPED TO REGULATOR
|
|
|
SPRING TENSION ON THE HOSE REEL FOR THE AUTOMATIC LUB SYSTEM IS
|
9 LBS +- 1/2 PDS
|
|
|
WHAT COLOR OF LIGHT WILL INDICATE FAULT IN THE AUTOMATIC LUB SYSTEM
|
RED LIGHT
|
|
|
A NEWLY RESTACKED ENGINE MUST BE SET AT HOW MANY COUNTS FOR 30 SECONDS FOR HOW MANY ARRESTMENTS
|
24 COUNTS FOR 50 ARRESTMENTS
|
|
|
HOW MANY TOTAL DISTRIBUTION BLOCKS FOR THE AUTOMATIC LUB SYSTEM ON THE MARK 7
|
SEVEN
|
|
|
THE MASTER DISTRUBITION BLOCK IS SET TO RELIEVE AT
|
2200 PSI
|
|
|
WHAT SHOT COUNT AND FOR HOW MANY SECONDS IS USED FOR THE AUTOMATIC LUB NORMAL AG OPERATIONS
|
18 COUNTS FOR 20 SECONDS
|
|
|
THE SECONDARY DISTRIBUTION BLOCK IS SET TO RELIEVE HOW MANY PSI
|
1800 PSI
|
|
|
WHAT IS THE PURPOSE OF THE CABLE ANCHOR DAMPER BACK TO THE BATTERY
|
3 WAY AIR VALVE WHICH UTILIZES A 100 PSI AIR SUPPLY
|
|
|
WHAT COLOR OF LIGHT WILL INDICATE THAT THE CABLE NACHOR DAMPER HAS RETURNED TO THE BATTER POSITION
|
GREEN LIGHT
|
|
|
WHAT IS THE PURPOSE OF THE CABLE ANCHOR DAMPER LFOW CONTROLE VALVE
|
IS A FLAPPER TYPE CHECK VALVE THAT ALLOWS FREE FLOW OF FLUID TO THE CALBE ANCHOR DAMPER ACCUMULATOR AND RESTRICTED FLOW OIN OPPPOSITE DIRECTION TO THE DAMPER CYLINDER
|
|
|
WHAT IS THE PURPOSE OF THE CUSHIONING PISTON ON THE CABLE ANCHOR DAMPER
|
PREVENTS OPERATIONG PISTON FROM SLAMMING INTO OPPOSIT END OF THE CABLE ASSEMBLY ASLO HELPFUL IN PURCHASE CABLE BREAK
|
|
|
WHAT IS THE SERVICE STROKE OF THE CABLE ANCHOR DAMPER ASSEMBLY
|
15 FT 8 INCHES
|
|
|
WHAT IS THE CONCEPT OF THE CABLE ANCHOR DAMPER ASSEMBLY
|
FLUID PRESSURE OVERCOMES CABLE TENSION UNTIL ALL CABLE SLACK IS REMOVED AND CABLE TENSION IS GREATER THEN FLUID PRESSURE ACTING ON THE OPERATING PISTON
|
|
|
WHAT IS THE PURPOSE OF THE SIGHT GLASS INDICATOR ON THE CALBE ANCHOR DAMPER ASSEMBLY
|
INDICATES FLUID HAS LEAKED INTO THE AIR SIDE
|
|
|
HOW MANY SLIPPERS ARE ON THE CABLE DAMPER ASSEMBLY
|
SIX
|
|
|
WHAT IS THE PURPOSE OF THE SHEAVE DAMPER ASSEMBLY
|
REDUCES PEACK CALBE TENSION BETWEEN THE LANDING AIRCRAFT AND THE ARRESTING GEAR ENGINE
|
|
|
WHAT DOES THE SHEAVE DAMPER ASSEMBLY CONSISTS OF
|
MOVEABLE CROSSHEAD, DAMPER CYLINDER, DAMPER PISTON ACCUMULATOR, PIPING, BUFFER ASSEMBLY, CHARGING PANEL
|
|
|
HOW MANY SLIPPERS DOES THE SHEAVE DAMPER ASSEMBLY HAVE
|
4
|
|
|
HOW MANY PSI IS THE SHEAVE DAMPER ASSEMBLY ACCUMULATOR CHARGED TO
|
750 PSI
|
|
|
WHAT IS THE PROPER SIGHT INDICATOR LEVEL FOR THE SHEAVE DAMPER ASSEMBLY WHEN IN THE BATTERY POSITION
|
2 INCHES +- 1 INCHES
|
|
|
WHAT IS THE PURPOSE FO THE MARK 7 ARRESTING GREA DECK GEAR ASSEMBLY
|
PORVIDES A MEANS OF ENGAGING A LANDING AIRCRAFT AND DIRECTING THE FORCE OF THE ARRESTMENT O THE ARRESTING GEAR ENGINE
|
|
|
NAME THE FOUR TYPES OF SHEAVES USED ON THE MARK 7 ARRESTING GEAR ENGINE
|
HORIZONTAL , THROUGH DECK, FAIRLEAD, RETRACTABLE SHEAVES
|
|
|
WHAT IS THE PURPOSE OF THE RETRACBLE SHEAVE
|
PROVIDES A MEANS OF LOWERING OR RAISING DECK SHEAVES
|
|
|
WHAT COLOR OF LIGHT WILL INDICAT E THAT THE AFFECTED RETRABLE DECK CSHEAVE HAS BEEN BYPASSED AND WHERE WIL YOU FIND THIS INDICATION
|
AN AMBER LIGHT LOCATED AT THE DECKEDGE STATION
|
|
|
WHAT MUST BE USED TO GO TO USING THE HADNWHEEL ON THE RETRACTABLE SHEAVE
|
THE DECLUTCH LEVER MUST BE THROWN IN THE COUNTERCLOCKWISE POSITION
|
|
|
WHAT ACTUATES THE TORQUE LIMIT SWITCH IN THE DOWN POSITION
|
TRIPPING PLATE WASHER
|
|
|
WHAT IS THE PURPOSE OF THE CLUTCH BEVEL GEAR
|
CAUSES ROTATION OF THE SLEEVE
|
|
|
DOES THE GEARED LIMIT SWITCH CONTROL THE RAISING OF THE RETRACTABLE SHEAVE
|
IN THE LOWERED POSITION
|
|
|
WHAT IS THE PROPER HEIGHT OF THE RETRACTABLE SHEAVE
|
4 7/8 INCHES +- OF AN INCH
|
|
|
WHAT IS THE DUPLEX CLOSURE RING USED FOR ON THE RETRACTABLE SHEAVE
|
IT IS USED AS A SEAL
|
|
|
HOW DO YOU CHECK THE LEVEL OF FLUID IN THE RETRACTABLE SHEAVE
|
BY CHECKING THE DIPSTICK
|
|
|
WHAT CAUSES THE WORM TO SLIDE ALONG THE WORMSHAFT ON THE RETRACTABLE SHEAVE
|
WHEN THER IS AN OBSTRUCTION UNDER THE SHEAVE AND THE FORCE EXERTED EXCEEDS NORMAL TORQUE WHICH IN TURN CAUSES WORM TO SLIDE ALONG WORMSHAFT PUSHING THE TRIPPING PLATE WASHER WHICH IN TURN OPENS THE TORQUE LIMIT SWITCH
|
|
|
WHAT IS THE DIAMER OF THE PURCHASE CABLE TO BE DETORQUED
|
MUST BE DETORQUED EVERY 50 TO 60 LANDINGS , EVERY 200+- 20 LANDNIGS THEREAFTER
|
|
|
WHAT SIZE OF CABLE SHOULD BE USED TO HANDREEVE A MARK 7 AG ENGINE
|
5/8 OR 3/4 INCH DIAMETER CABLE
|
|
|
WHAT IS THE REPLACEMENT CRITERIA FOR THE AG PURCHASE CABLE
|
4 MORE BROKEN WIRES IN ONE ROPE LAY 12 OR MORE BROKEN WIRES IN THE ENTIRE LENGTH
|
|
|
HOW OFTEN IS THE PURCHASE CABLE INSPECTED
|
IT IS CHECKED MONTHLY OR EVERY 300 ARRESTMENTS UNTIL 1000 ARRESTMENTS THEN WEEKLY OR EVERY 100 ARRESTMENTS UNTIL 2000 ARRESTMENTS
|
|
|
WHEN WILL A PURCHASE CABLE BE REPLACED ON THE MARK 7 AG ENGINE FOR AS FAR AS Q FACTORS IS CONCERNED
|
WHEN THE Q FACTORS FOR THE FIRST 15 FEET OF CABLE ARE 8 INCHES OR LESS, 9 INCHES OR LESS FOR THE REMAINDER OF THE CABLE
|
|
|
WHAT IS THE DIAMETER AND CONSTRUCTION OF THE CROSS DECK PENDANT
|
THE DIAMETER IS THE 1 3/8 INCHES AND THE CONSTRUCTION IS 6X30
|
|
|
WHAT IS THE BREAKING STRENGTH OF THE CROSS DECK PENDANT
|
188000 LBS
|
