Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
42 Cards in this Set
- Front
- Back
When is a mechanic responsible for checking A.D. compliances? |
When performing an inspection required under part 91, 125, or 135 |
|
Check thrust bearing nuts for tightness on new or newly overhauled engines at the first inspections following installation. |
150 hours |
|
Aviation maintenance alerts |
Provide information about aircraft problems and suggest corrective action. |
|
The -100 in the title block applicable to which doubler part number? |
-101 |
|
What regulations are covered by 14 CFR part 1 |
Definitions and abbreviations |
|
A complete detailed inspection and adjustment of a valve mechanism will be made at the first 25 hours after the engine has been placed in service. At what interval will valve mechanism inspection be performed? |
100 hours |
|
What is the maximum penalty for cheating or other unauthorized conduct when taking a FAA mechanic test? |
Ineligibility to receive any certificate or rating for one year, and suspension or revocation of any certificate held |
|
How long are A. D. Compliance records required to be kept? |
They shall be retained, and then transferred with the aircraft when it is sold. |
|
Which regulation provides the airworthiness standards for an airplane certification in the normal category? |
14 CFR part 23 |
|
What does the type certificate data sheet designation code 2 P.C.S.M. mean? |
2 place, Closed, Sea, Monoplane, |
|
A TSO Is used by whom? |
The administrator |
|
An aircraft type certificate data sheet contains |
Location of Datum |
|
Which regulation provides information regarding instrument range markings for an airplane certified in the normal category? |
14 CFR part 23 |
|
1. Manufacturers data and FFA publications such as airworthiness directives, type certificate data sheets..... 2. FAA publications such as technical standard orders, airworthiness directives... |
Only Number two is true |
|
Suitability for use of specific propellers with a particular engine-airplane combination can be determined by reference to what informational source? |
Aircraft specification or aircraft type certificate data sheet |
|
The following words are an example of what part of statement in an A. D.? |
Compliance |
|
Specifications pertaining to an aircraft model manufactured under a type certificate, of which less than 50 are shown on the FAA aircraft registry, can be found in the |
Aircraft listing |
|
1. A supplemental type certificate may be issued two more than one applicant for the same design change.... 2. In installation of an item manufactured in accordance with the technical standard order system requires no further approval.... |
Only number one is true |
|
How many parts will need to be fabricated by the mechanic in the construction and installation of 1 doubler? |
3 |
|
1. Propellers are not included in the airworthiness directive. 2. A certified PowerPlant mechanic may make and minor repair on an aluminum propeller.... |
Only number two is true |
|
An aircraft mechanic is privileged to perform major alterations on US certified aircraft. Which is not approved data? |
AC 43.13 - 2A |
|
Technical information about older aircraft models, of which no more than 50 remain in service, can be found in the |
Aircraft listing |
|
Using only the information given.... which doubler is it possible to construct and install? |
-101 |
|
Airworthiness directives are issued primarily to |
Correct an unsafe condition |
|
Where are technical descriptions of certified propellers found? |
Propeller type certificate data sheets |
|
Which of the following includes all the regulatory descriptions of maintenance? |
Overhaul, repair, replace parts, preservation, inspection, and preventive maintenance |
|
The following is a table of are speed limits as given in A FAA issued aircraft specifications |
139 knots |
|
Type certificate data sheets are issued for which of the following products? |
Aircraft, engines, and propellers |
|
Primary responsibility for compliance with airworthy directives lies with the |
Aircraft owner and operator |
|
When an airworthy aircraft is sold, the airworthiness certificate |
Is transferred with the aircraft |
|
1. The FAA requires approval after compliance with the data of a supplemental type certificate. 2. an installation of an item manufactured in accordance with the technical standard order system requires no further approval |
Only number one is true |
|
What does the acronym TSO mean? |
Technical standard order |
|
The air transport association of America specification number 100.... 1. Establishes a standard for the presentation of technical data and maintenance manuals. 2. Divides the aircraft into numbered systems and subsystems. |
Both number one and number two are true |
|
Which of the following are sometimes used as authorization to deviate from an aircraft original type design? |
1. FAA form 337 2. Supplemental type certificate 3. Airworthiness directive |
|
Placards required on an aircraft are specified in |
Aircraft specifications or type certificate data sheets |
|
under the Federal aviation regulations, and aviation maintenance technician is required to perform maintenance on an aircraft so that it |
Is at least equal to its original or priority altered condition. |
|
An aircraft has a total time in service of 468 hours. The airworthiness directive given was initially completed at 454 hours in service. How many additional hours in service maybe accomplished before the airworthiness directive must again be completed? |
186 |
|
What information is generally contained in aircraft specifications or type certificate data sheets? |
Control surface movement |
|
Which doublers require heat treatment before installation |
-102 |
|
The action required by an A.D. may take what form? |
1. Inspection 2. Part replacement 3. Design modification And or 4. Change in Operating procedures |
|
What is the maintenance recording responsibility for the person who complies with an airworthiness directive? |
Make an entry in the maintenance records of that equipment |
|
The issuance of an Airworthiness Certificate is governed by |
14 CFR part 21 |