Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
27 Cards in this Set
- Front
- Back
What specific peices of equipment uses two-stroke gas?
|
K-1200 Partner
K-950 Partner STIHL TS 350 Rescue Saw STHIL Chain Saw Home Lite 330 Chain Saw |
|
What ratio gasoline stabilizer do we use?
|
Use TK-7 1/8 ounce per gallon of gasoline ratio. FYI I dont think we even use this any more
|
|
What two brand names of two cycle oil do we use?
|
STHIL or HUSKY
|
|
What is the fuel mixture ratio we use for two stroke engines?
|
40 to one > OR 2 1/2 gallons to 8 ounces.
|
|
What is a granular material which in contact with water forms an immediate seal to plug, divert, and confine flammable liquids and hazardous spills?
|
PB-35 Plug and Dike
|
|
PB-35 is a combination of what two things?
|
High water absorption polymer in a bentonite base
|
|
The polymer in PB-35 will absorb over ???? times its own weight in water??
|
150 times
|
|
Will PB-35 prevent the flow of gasoline through it?
|
yes
|
|
How longe wil PB-35 last when used?
|
As long as it is maintained wet and also 4-8 hours easily
|
|
How does PB-35 hold up under heat?
|
Holds up well even under intense heat.
|
|
How many feet/head of liquid can PB35 hold?
|
12-15 foot/head
|
|
Can PB35 be used to plug high pressure lines and breaks?
|
No, but it can be used to controll that spill by diking and confining it at the point where it comes in contact with the ground and the pressure is now reduced to a flow.
|
|
Power tool safety, - how many feet away from the fueling point should the cutting machine be?
|
10 feet
|
|
How far should you move a cutting machine away from a fuel point before starting it?
|
At least 10 feet
|
|
What % will the lockout tool kit get into?
|
99%
|
|
What can be used to limit damage to paint and rubber insulation on a car while using the lock out kit?
|
Masking tape
silicone soap (wetting agent) |
|
Where is the instructions for the lock out tool kit kept?
|
With the tool
|
|
How much wetting agent is added to the water extinguisher?
|
1 cap
|
|
When do we check/inspect our extinguishers?
|
The first apparatus day of the month. It is also on our Apparatus check list for mondays. So It may just be mondays.
|
|
Where do we send broken CO2 cartidges?
|
Sta 32
|
|
What month is the annual maintenance done?
|
Feb.
|
|
When filling the H2O extinguisher how much of each substance is needed?
|
Two and a half gallons of water and a cap full of wetting agent.
|
|
How much water and wetting agent is to be added to the extiguisher?
|
Two and a half gallons and one cap of wetting agent.
|
|
In reference to PB-35, the polymer will absorb ____ times it's own weight.
|
150
|
|
Can PB-35 be used on a spill where fire is involved? If so what is the procedure?
|
Yes, use more water as the heat may tend to partially dry out the PB-35 with time.
|
|
PB-35 can be used for up to ____ head pressure
|
8-10 foot head of liquid (note: policy says 12-15 but the actual package says 8-10)
|
|
The K1200 uses what type of fuel?
|
Unleaded gasoline
|