Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
217 Cards in this Set
- Front
- Back
- 3rd side (hint)
Code to follow when performing an internal inspection on pipe |
API 510 |
|
|
Positive material identification (PMI) |
API 578 |
|
|
Fitness for service (FFS) |
API 579 |
|
|
Risked based inspection (RBI) |
API 580 |
|
|
Corrosion under insulation (CUI) |
API 583 |
|
|
Valve inspection and testing |
API 598 |
|
|
Cathodic protection |
API 651 |
|
|
Welding on in service equipment |
API 2201 |
|
|
NDE procedure guidelines |
ASME sect V |
|
|
Design code for fabrication of piping relief devices |
ASME section 8 |
|
|
Welder and weld procedure qualification |
ASME section 9 |
|
|
NDE personal qualification |
ASME SNT-TC-1A or CP-189 |
|
|
API 570 scope |
AIRR (Alteration. Inspection, repair,rerate) |
|
|
API 570 AI employer |
JUIC (Jurisdiction, user, insurance company, contractor) |
|
|
API 570 repair organization |
JOC (Authorized by Jurisdiction, owner, contractor) |
|
|
Primary responsibility of API 570 AI |
A TIE (Testing, inspection,Examination ) |
|
|
Determine corrosion rate for new service or change in service |
SOPI (Same or similar service, owners experience, published data, inspect in last 3 months) |
|
|
Define- alteration |
Physical change |
|
|
NDE- number of CMLs to obtain thickness readings during inspection |
Representative |
|
|
NDE- cml that must be measured during a thickness inspection |
CML w/ earliest renewal date |
|
|
PRD’s how relief devices intervals are determined |
Performance |
|
|
Corrosion-type of soil that is most corrosive |
Low resistivity |
|
|
Corrosion- factors the affect the creep rate |
Time. Temp. Stress |
|
|
Mill tolerance for rolled and welded pipe |
-0.010” |
|
|
NDE- maximum length of crack or incomplete fusion allowed on a new weld |
0” |
|
|
Typical flange face finish |
125-250 micro inch |
|
|
When mating flanges the maximum amount of unparallel allowed (per diameter of flange in feet) |
1/16” per foot |
|
|
Max offset for bolt holes for mating flanges |
1/8” |
|
|
Define- repair |
Restore-suitable |
|
|
Corrosion-cause for fatigue crack |
Cyclic stress |
|
|
Define- imperfection that exceeds the acceptance criteria |
Defect |
|
|
Corrosion- factors the affect the creep rate |
Time. Temp. Stress |
|
|
Define- RPI’s two primary factors |
Probably and consequence |
|
|
RBI- two primary factors of consequence of failure |
Process fluid and volume |
|
|
Repairs- # of new flange assemblies to be inspected during repairs and alterations |
Representative |
|
|
Inspection- basis of API 570s piping classification |
Consequence of failure |
|
|
Corrosion- method by which process leaks can lead to brittle failure |
Auto refigeration |
|
|
Maximum allowed size of open discontinuity in a bend test |
1/8” |
|
|
NDE-distance of eye to part to count as a visual exam |
6-24” |
|
|
Corrosion- soil to air area- distance in soil from interface |
12” |
|
|
NDE- minimum upstream limit of intensive examination of inspection point circuit |
12” |
|
|
Minimum overlap for PWHT when using multiple heats |
12” |
|
|
Minimum distance beyond the area to be examined to clean a part when performing a MT or PT examination |
1” |
|
|
Minimum radius of insert patch |
1” |
|
|
Suggested diameter of cml exam point |
2” |
|
|
Preheat zone- minimum width of band |
3T |
|
|
NDE- minimum length of spot RT |
6” |
|
|
Minimum weld length when qualifying a welder with RT/UT using a coupon or 1st production weld |
6” |
|
|
Minimum weld length when qualifying a welding operator with RT/UT of a test coupon |
6” |
|
|
Corrosion-Soil to air area- distance in air from surface |
6” |
|
|
Corrosion- distance to dig when inspecting for soil to air corrosion |
6-12” |
|
|
Minimum weld length when qualifying a welding operator with RT/UT of first production weld |
3’ |
|
|
Subject to chloride stress corrosion cracking |
300-SS |
|
|
Subject to polytheonic acid stress corrosion cracking |
Sensitized 300 SS |
|
|
P#s allowed to use pre heat in lieu of PWHT |
P1&P3 |
|
|
P#s allowed to use controlled deposition in lieu of PWHT |
P1,P3,P4 |
|
|
CUI affects carbon steel and low alloy (temp range) |
10-350F |
|
|
UT calibration- UT block must be within what temp of the part to be examined |
25F |
|
|
Standard temp range for a PT exam |
40-125F |
|
|
Minimum flash point of hydrocarbons used for leak testing |
120F |
|
|
CUI affects austentic SS (temp range) |
140-350F |
|
|
Temperature where chloride stress corrosion cracking becomes a concern |
> 140F |
|
|
Minimum length of buried pipe to expose when excavating for inspection |
6-8’ |
|
|
Temp where Special procedure needed for UT thickness readings |
>150F |
|
|
Most aggressive CUI range |
212-350F |
|
|
Minimum pre heat temp when preheat is substituted for PWHT |
300F |
|
|
Minimum preheat temperature when a local PWHT is substituted for a full encirclement PWHT |
300F |
|
|
Starting temperature for sulfidation on carbon steel per api 574 |
500F |
|
|
Starting temp for sulfidation on iron based alloys per api 570 and api 571 |
500F |
|
|
Operating temp when a corrosion specialist must input on an inspection plan |
> 750 F |
|
|
Graphitization occurs in carbon steel materials |
Greater than or equal to 800F |
|
|
Temp-Creep occurs in 1-1/4% chrome materials |
>900 |
|
|
Maximum temperature for UT readings per sect V |
1000F |
|
|
Maximum size of fillet weld patch on pipe |
1/2 diameter |
|
|
Maximum temperature for UT readings per API 574 using special decay lines and water cooled transducer |
1100F |
|
|
CS HAZ- base metal that did not melt but exceeded this temp during welding |
1350F |
|
|
Minimum base metal temp during pressure test when wall thickness is <2” thick |
MDMT +10F |
|
|
Minimum base metal temp during pressure test when wall thickness is >2” thick |
MDMT + 30F |
|
|
Max temperature for magnetic particles |
Manufacture recommended |
|
|
Maximum upstream limit of injection point circuit |
Greater of: 12” or 3 Dia |
|
|
Minimum downstream limit of intensive examination of injection point circuit |
10 diameters |
|
|
Minimum downstream limit of injection point circuit |
Lesser of: 1st direction change +25’ or 2nd direction change |
|
|
Linear indications |
Length is greater than or equal to 3 times the width |
|
|
Common material with an endurance limit |
CS |
|
|
Subject to temper embrittlement |
Low chromes |
|
|
Common material w/o an endurance limit |
SS |
|
|
Flanges- minimum thread engagement acceptance criteria per API 570 |
-1 thd |
|
|
Flanges- minimum thread engagement acceptance criteria per B31.3 |
-0 thd |
|
|
Ratio of endurance limit stress to ultimate tensile stress for carbon steel |
0.4-0.5 |
|
|
Minimum range of pressure gauge used during pressure test (multiplied by test pressure) |
1.5 |
|
|
Impact test- number of test bars required in each set |
3 |
|
|
When using a shin under a hole type IQI, the number of sides of the IQI that must be seen in the RT image |
3 |
|
|
Number of additional welds or joints to examine when a weld defect is found during a random examination |
2 |
|
|
Preferred range of pressure gauge used during pressure test (multiplied by test pressure) |
2 |
|
|
Maximum range of pressure gauge used during pressure test (multiplied by test pressure) |
4 |
|
|
Number of additional welds of joints to examine when a weld defect is found during a random examination |
2 |
|
|
PWHT- # of thermocouples required when performing a local PWHT instead of a 360 degree band |
2 |
|
|
Weld qualification-Number of tension test to qualify a WPS |
2 |
|
|
Weld qualification- number of bend test to qualify a welder or welding operator in welding positions 1G-4G |
2 |
|
|
Minimum number of exposures to RT 360 of a weld using a double wall technique double wall view (elliptical) |
2 |
|
|
RT film density range allowed of a weld and IQI when using a gamma ray source |
2.0-4.0 |
|
|
Minimum number of exposures to RT 360 of a weld using a double wall technique. Single wall view |
3 |
|
|
Number of bend test to qualify a welder or welding operator in welding positions 5G&6G |
4 |
<50ppm
|
|
Minimum time an examiner should be in a darkened area prior to using a black light for MT&PT exams |
5min |
|
|
Minimum duration for a pressure test per B31.3 |
10 min |
|
|
Final interpretation of a PT exam after application of developer (time range) |
10-60 min |
|
|
Minimum duration for a pressure test per API 577 |
30 min |
|
|
Minimum duration of hydro to evaluate integrity of buried pipe |
8 hours |
|
|
Max external inspection interval for class 1&2 piping |
5years |
|
|
Maximum interval for relief devices in fouling or corrosive service |
5years |
|
|
Suggested interval for class interval potential survey of buried pipe with poor CP |
3-5 years |
|
|
Max time a welder or welding operator maintains qualifications for a process without using |
6 months |
|
|
Suggested interval for. Above graded visual surveillance of buried pipe |
6 months |
|
|
Maximum interval for relief devices in non fouling or non corrosive service |
10 year |
|
|
Minimum years of experience for owners inspector during new fabrication |
10 years |
|
|
Maximum external inspection interval for class 3 piping |
10 years |
|
|
Max thickness inspection interval for an injection point |
Lesser: 3yr or half-life |
|
|
Max calibrating interval- RT densitometer |
90 days |
|
|
Minimum time for obtaining thickness readings when corrosion rate on new pipe is not known (no other data available) |
3 months |
|
|
Max time a welder or welding operator maintains qualifications for a process without using ryhst procrastination |
6 months |
|
|
Suggested interval for. Above graded visual surveillance of buried pipe max |
6 months |
|
|
Max interval for for a visual examiners eye exam |
1 year |
|
|
Max interval to calibrate pressure gauge used in testing |
1 year |
|
|
Length of time before an API 570 AI must recertify |
3 years |
|
|
Max thickness inspection interval for an for an injection point |
Lesser: 3yr or half-life |
|
|
Maximum interval for RBI reassessment |
10 years |
|
|
NDE- maximum pipe size for performing an elliptical shot |
3 NPS |
|
|
Pipe sizes can use profile RT to find localized corrosion |
Less than or equal 8 NPS |
|
|
Pipe size where where pipe OD is equal to pipe size (NPS) |
Greater than or equal to 14 |
|
|
Pipe size where pipe is almost always made using rolled and welded plate |
Greater than 16 NPS |
|
|
Weight used to check magnetic strength of an AC yoke |
10lbs |
|
|
Weight used to check magnetic strength of a magnetic DC yoke |
40lbs |
|
|
Maximum thickness inspection interval for class 2&3 piping |
Lesser: 10year or half life |
|
|
When should a temporary welded pipe repair be replaced |
Next opportunity |
|
|
When shall non-welded repairs and temporary leak sealing devices be removed and pipe replaced |
Next turnaround |
|
|
Max calibrating interval- check the light intensity of a black light used in a MT or PT exam |
Before and after use |
|
|
Pipe size where RT is preferred for thickness readings |
Less than or equal 1NPS |
|
|
Pipe size where UT thickness readings may require specialized equipment |
Less than or equal 2 NPS |
|
|
Small bore piping |
Less than or equal 2 NPS |
|
|
Maximum pipe size normally allowed for threaded pipe |
Less than or equal 2 NPS |
|
|
Maximum pipe size normally allowed for socket welded pipe |
Less than or equal 2 NPS |
|
|
Weight used to check magnetic strength of a permanent magnet yoke |
40lbs |
|
|
Minimum angle of eye to part to count as a visual exam |
30 degrees |
|
|
Two primary gamma-ray RT sources |
It-192 Cobalt-60 |
|
|
Weld qualification- which welding process can a welder NOT be qualified by RT/UT |
GMAW-SC |
|
|
Welding- variables needed on WPS |
Essential and non essential |
|
|
Welding- minimum taper required for welds with mismatch |
30 degrees |
|
|
Two most common CS materials |
A106 A53 |
|
|
Maximum stress allowed during a pressure test |
90% of SMYS |
|
|
Repair- maximum allowed SYMS for pipe if fillet welded patch is installed |
40,000psi |
|
|
Lead letter used during RT to check for backscatter |
B |
|
|
Lead letter used during RT to check for film side IQI |
F |
|
|
Hole size that must be visible during RT when using a hole type IQI |
2T |
|
|
NDE- minimum black light intensity when performing non-fourescent MT or PT or VT exams |
100ft candles |
|
|
Minimum black light intensity when performing MT or PT fluorescent exams |
1000mW/cm2 |
|
|
Maximum UT scanning speed |
6”/second |
|
|
Maximum allowed thickness on a WPS based on the plate thickness (T) of a PQR test coupon |
2T |
|
|
Weld qualification- the “all position” test coupon |
6G |
|
|
Weld qualification- reject-able in RT when qualifying a welder |
Crack, IP, LoF |
|
|
Two primary gamma-ray RT sources |
It-192 Cobalt-60 |
|
|
Weld qualification- which welding process can a welder NOT be qualified by RT/UT |
GMAW-SC |
|
|
Welding- variables needed on WPS |
Essential and non essential |
|
|
Welding- minimum taper required for welds with mismatch |
30 degrees |
|
|
Two most common CS materials |
A106 A53 |
|
|
Maximum stress allowed during a pressure test |
90% of SMYS |
|
|
Repair- maximum allowed SYMS for pipe if fillet welded patch is installed |
40,000psi |
|
|
Test- ph of water needed to reduce likelihood of MIC (bugs) |
>10ph |
|
|
Test- pressure to perform inspection during a pressure test of pipe that has been in service |
Less than or equal MAWP |
|
|
Typical external corrosion rate for dry rural areas |
<1mpy |
|
|
Typical external corrosion rate for inland locations with moderate rain and humidity |
1-3 mpy |
|
|
Lead letter used during RT to check for backscatter |
B |
|
|
Possible external corrosion rate for industrial environments with acid or Sulphur compounds |
5-10 mpy |
|
|
Possible external corrosion rate for marine locations |
20 mpy |
|
|
Most commonly used welding process |
SMAW |
|
|
GMAW transfer mode most likely to have LoF |
Short circuit |
|
|
Most extensively used NDE method for welds |
Visual |
|
|
Weld metal is most similar to what fab process |
Casting |
|
|
Meaning of 1st two digits in the electrode designation for a SMAW electrode |
Strength |
|
|
Meaning of “S” in the electrode designation for a GMAW or GTAW electrode |
Solid wire |
|
|
RT film density of weld as compared to IQI (range) |
-15% to 30% |
|
|
Mill tolerance for seamless pipe |
-12.5% |
|
|
Most commonly used welding process |
SMAW |
|
|
Hole size that must be visible during RT when using a hole type IQI |
2T |
|
|
NDE- minimum black light intensity when performing non-fourescent MT or PT or VT exams |
100ft candles |
|
|
Minimum black light intensity when performing MT or PT fluorescent exams |
100 mW/cm2 |
|
|
Maximum UT scanning speed |
6”/second |
|
|
Maximum allowed thickness on a WPS based on the plate thickness (T) of a PQR test coupon |
2T |
|
|
Weld qualification- the “all position” test coupon |
6G |
|
|
Weld qualification- reject-able in RT when qualifying a welder |
Crack, IP, LoF |
|
|
RT film density of weld as compared to IQI (range) |
-15% to +30% |
|
|
% of welds to RT/UT when fabricating norm service pipe |
5% |
|
|
%of welds to VT when fabricating normal service pipe |
5% |
|
|
Overlap with a UT scan, % of transducer diameter |
10% |
|
|
Amount of time inspector must be involved in inspection activities-required to maintain API-570 certification |
20% |
|
|
Amount of nickel required for a material to be considered a nickel alloy |
>30% |
|
|
% of visual and RT/UT required when fabbing severe cyclic pipe |
100% |
|
|
Testing- Minimum pneumatic test pressure, % of design pressure |
110% |
|
|
Testing-minimum test pressure for underground pipe. % of maximum operating pressure (testing in lieu of digging) |
110% |
|
|
PRV- maximum set pressure for thermal relief valves, %of design pressure |
120% |
|
|
Hydro-maximum chloride content of water when hydro testing austentic ss |
<50ppm |
|
|
Document owner/user must have that is following API 570 |
QA/repair manual |
|
|
Document required when owner audits inspection program |
Tracking system |
|
|
Document required of examiners employer |
Certification records |
|
|
Document required for each piping system |
Inspection plan |
|
|
Document required for each PRD repair organization |
QA manual |
|
|
Document required concerning personal at PRD repair organization |
Training program |
|
|
Relatively uniform corrosion |
Sulfidation Sour water |
|
|
Valves that should be inspected for thermal fatigue |
Cat reformer |
|
|
Another record that the owner/user must maintain |
Inspection ISO’s |
|
|
Another record that the owner/user must maintain |
Track repairs recommendations |
|
|
Another record that the owner/user must maintain |
External inspections |
|
|
Another record that the owner/user must maintain |
Track temporary repairs |
|
|
Another record that the owner/user must maintain |
Deferrals |
|
|
Records maintain by repair organization and available to the inspector |
WPS&WPQ |
|
|
SCC can develop at hot spots, including where the heat tracing attaches to pipe |
Caustic |
|
|
Where dew point corrosion often occurs |
Overhead fractionation |
|
|
Potential for none or very few cmls on circuit |
Olefin cold side Anhydrous ammonia |
|