Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
25 Cards in this Set
- Front
- Back
Multiple choice:
Cutting all the hair to one length is a/an ____ cut. A. elevation B. blunt C. graduated D. beveled |
Answer: B. BLUNT
Cutting all the hair to one length is a/an ____ cut. |
|
Multiple choice:
A cut that has a stacked area around the exterior and is cut at low to medium elevations is a/an _____ cut. A. elevation B. blunt C. graduated D. beveled |
Answer: C. GRADUATED
A cut that has a stacked area around the exterior and is cut at low to medium elevations is a/an _____ cut. |
|
Multiple choice:
Cutting with the points of the shears to create texture is known as ____. A. layering B. undercutting C. elevation D. notching |
Answer: D. NOTCHING
Cutting with the points of the shears to create texture is known as ____. |
|
Multiple choice:
Subdivisions of a section, used for control when cutting are known as ____. A. subsections B. guides C. sections D. tension |
Answer: A. SUBSECTIONS
Subdivisions of a section, used for control when cutting are known as ____. |
|
Multiple choice:
If the hair is cut partially wet and partially dry, the results will be ____. A. even B. perfect C. uneven D. curly |
Answer: UNEVEN
If the hair is cut partially wet and partially dry, the results will be ____. |
|
Multiple choice:
The tools also known as trimmers that are used to clean necklines and around the ears are ____. A. clippers B. edgers C. razor D. shears |
Answer: B. EDGERS
The tools also known as trimmers that are used to clean necklines and around the ears are ____. |
|
Multiple choice:
A tool used to cut blunt straight lines is called the ____. A. clippers B. edgers C. razor D. shears |
Answer: D. SHEARS
A tool used to cut blunt straight lines is called the ____. |
|
Multiple choice:
The tool used to cut hair with a softer edge is known as the ____. A. clippers B. edgers C. razor D. shears |
Answer: C. RAZOR
The tool used to cut hair with a softer edge is known as the ____. |
|
Multiple choice:
The comb used for close tapers in the nape and sides is the ____ comb. A. styling B. barber C. wide-tooth D. tail |
Answer: B. BARBER
The comb used for close tapers in the nape and sides is the ____ comb. |
|
Multiple choice:
The comb used mainly to detangle the hair is the ____. A. styling B. barber C. wide-tooth D. tail |
Answer: C. WIDE-TOOTH
The comb used mainly to detangle the hair is the ____. |
|
Multiple choice:
____ points are points on the head that mark where the surface of the head changes or the behavior of the hair changes, such as the ears, jawline, occipital bone, or apex. A. parietal B. crown C. elevation D. reference |
Answer: D. REFERENCE
____ points are points on the head that mark where the surface of the head changes or the behavior of the hair changes, such as the ears, jawline, occipital bone, or apex. |
|
Multiple choice:
____ lines are parallel to the floor. A. horizontal B. perpendicular C. diagonal D. vertical |
Answer: A. HORIZONTAL
____ lines are parallel to the floor. |
|
Multiple choice:
Lines that are perpendicular to the floor are ____ lines. A. parallel B. perpendicular C. diagonal D. vertical |
Answer: D. VERTICAL
Lines that are perpendicular to the floor are ____ lines. |
|
Multiple choice:
A haircutting technique that is measured in degrees is ____. A. carving B. elevation C. clipper-over-comb D. traveling |
Answer: B. ELEVATION
A haircutting technique that is measured in degrees is ____. |
|
Multiple choice:
Lines that are used for blending and stacking are ____ lines. A. parallel B. perpendicular C. diagonal D. vertical |
Answer: C. DIAGONAL
Lines that are used for blending and stacking are ____ lines. |
|
Multiple choice:
A stable guide that does not move is also known as a ____ guide. A. moving B. traveling C. stationary D. mobile |
Answer: C. STATIONARY
A stable guide that does not move is also known as a ____ guide. |
|
Multiple choice:
When the hair is cut at 90 degrees and higher, the result is a ____ haircut. A. blunt B. layered C. graduated D. blended |
Answer: B. LAYERED
When the hair is cut at 90 degrees and higher, the result is a ____ haircut. |
|
Multiple choice:
A 180-degree haircut is also known as a ____. A. low elevation cut B. combined elevation cut C. long layered haircut D. blended elevation cut |
Answer: C. LONG LAYERED HAIRCUT
A 180-degree haircut is also known as a ____. |
|
Multiple choice:
A 0-degree haircut is also known as a ____ elevation. A. low B. high C. reverse D. blended |
Answer: A. LOW
A 0-degree haircut is also known as a ____ elevation. |
|
Multiple choice:
A barbering technique that has become popular with cosmetologists is the ____ -over-comb method. A. clipper B. razor C. trimmer D. shears |
Answer: D. SHEARS
A barbering technique that has become popular with cosmetologists is the ____ -over-comb method. |
|
Multiple choice:
A/an ____ is a thin continuous mark used as a guide. A. angle B. line C. elevation D. section |
Answer: B. LINE
A/an ____ is a thin continuous mark used as a guide. |
|
Multiple choice:
Gliding the fingers and shears along the edge of the hair to remove length is called ____ cutting. A. point B. slide C. notching D. razor |
Answer: B. SLIDE
Gliding the fingers and shears along the edge of the hair to remove length is called ____ cutting. |
|
Multiple choice:
The process of thinning with scissors is known as ____. A. effilating B. shaving C. sliding D. trimming |
Answer: A. EFFILATING
The process of thinning with scissors is known as ____. |
|
Multiple choice:
____ guides are used mostly in blunt (one-length) haircuts or when using overdirection to create a length or weight increase in a haircut. A. traveling B. movable C. stationary D. portable |
Answer: C. STATIONARY
____ guides are used mostly in blunt (one-length) haircuts or when using overdirection to create a length or weight increase in a haircut. |
|
Multiple choice:
____ is used mostly in graduated and layered haircuts, and in those situations where a length increase in the design is desired. A. effilating B. trimming C. elevating D. overdirection |
Answer: D. OVERDIRECTION
____ is used mostly in graduated and layered haircuts, and in those situations where a length increase in the design is desired. |