Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
67 Cards in this Set
- Front
- Back
Technical orders provide all of the following pertaining to the inspection, operation, maintenance, and modification of Air Force equipment and material except: |
Policy Directives |
|
Simply stated, a technical order is considered to be: |
a military order |
|
Technical Orders are established, numbered, and issued in accordance with which TO? |
00-5-1 |
|
Which type of TO covers installation, troubleshooting, repairing, removing, calibration, and servicing or handling of Air Force military systems? |
Operations and maintenance TOs |
|
ETIMS provides a direct on-line connectivity from every base into the management system to allow all except: |
most current publication date |
|
To find the most current publication date of a TO, check |
the TO index |
|
MIDAS is: |
a six digit numbering system expressed as three elements of two digits each |
|
What information does the NDI general system (GS) manual provide? |
Inspections |
|
What type of vehicle equipment manual would contain calibration requirements? |
Operation and service manual |
|
A group assembly parts list has several part numbers listed for a part you need. To determine which part number is right for your aircraft, refer to the |
useable on code condition |
|
Where would you find information for recording and reporting a nondestructive inspection (NDI) technique to inspect an F-16C speed brake? |
TO 33B-1-1 |
|
You are tasked to do an inspection; however you only know the name of the part you are to inspect. To locate the applicable paragraph and figure number for the inspection, check the TO's |
alphabetical index |
|
While doing a job you find a mistake in a TO. Correcting this requires initiation of a Technical Manual Change Recommendation and Reply form. Who is responsible for this action? |
You |
|
Which change recommendation priority must be answered within 40 calender days? |
Urgent |
|
Which type change recommendation priority is used to recommend improvements to correct potential hazards? |
Routine |
|
Which technical order (TO) contains complete instructions for maintaining TOs? |
00-5-1 |
|
Electronic Technical orders (TO) are files identified by a media distribution code suffix of |
-WA-n |
|
You need to order a new technical order (TO) for personnel use on a regular basis; how would you accomplish this action? |
Establish an ID requirement |
|
The technical order (TO) listing for your shop's operational TO file will show you all of the following except |
who currently has one signed out |
|
Responsibility for consolidating technical order (TO) requests on an installation rests with the |
personnel in the TODO |
|
With few exceptions, you must file technical orders (TO) within a maximum of |
five work days of receipt |
|
A technical order (TO) effective date is |
later than the basic date |
|
In which technical order (TO) chapter would you find page 4-2? |
4 |
|
File technical order (TO) supplements in |
reverse numerical order in front of the basic TO |
|
ETIMS will be updated automatically in no more than how many days? |
7 calendar days |
|
Who has ownership of Air Force supplies and equipment? |
American taxpayer |
|
The purpose of the Air Force supply system is to |
provide a means of purchasing, distributing, and controlling equipment/supplies used by the Air Force |
|
Which system is used to determine whether your NDI laboratory is authorized a piece if equipment? |
AFEMS |
|
Which form is used to request an item not listed in the Federal Supply System? |
DD Form 1348-6 |
|
Which condition tag would be placed on an eddy current unit sent back to depot for repair? |
Green DD Form 1577-2 |
|
All of these are requirements for an initial journeyman skill level except you must |
complete 9 months of on-the-job training |
|
From the lowest to the highest , what are the three levels of maintenance capability? |
Organizational, intermediate, depot |
|
Which level of maintenance involves major repairs and overhaul? |
Depot |
|
Which inspection involves a thorough and searching review of an entire weapon system? |
Periodic (PE) |
|
Which inspection attempts to minimize the length of time an aircraft is down for inspection? |
Phase (PH) |
|
Which inspection is based on calendar days? |
Isochronal (ISO) |
|
Which maintenance symbol would be used to indicate a scheduled periodic (PE) inspection is overdue? |
Red Dash |
|
Which symbol signifies that an unsatisfactory condition exists? |
Red Diagonal |
|
Category I deficiency reports (DR) are not used to report conditions |
resulting from nonconformance to specifications |
|
Maintenance data documentation (MDD) is grouped into what categories? |
On- and off-equipment |
|
You would not find maintenance data documentation (MDD) rules in |
TO 00-35D-54 |
|
Maintenance information system (MIS) refers to an automated maintenance information system that supports and enables what? |
Maintenance business procedures |
|
Which maintenance data documentation code (MDD) codes to simplify reporting? |
How malfunctioned |
|
Which is NOT a maintenance inspector function? |
Verify the quantity of modified parts is correct |
|
All engine flight data can be found on Air Force Technical Order (AFTO) Form |
781J |
|
What is the correct format for entering a date in the 781 series forms? |
YYYYMMDD |
|
Which blocks are used by nondestructive inspection (NDI) personnel to clear all red dash discrepencies? |
Inspected by and employee no. blocks |
|
What is used to record service, periodic, and special inspections, and the current status of equipment? |
AFTO 244 |
|
What indicates a special inspection or operational check is due, a scheduled inspection is overdue, and the equipment is in an unknown condition? |
A red dash |
|
What is a database developed for the NDI career field in an effort to reduce paper and improve the management of process controls and equipment maintenace? |
PCAMS |
|
What are commanders, staff officers, and supervisors responsible for when it comes to accident prevention? |
Standards and regulations |
|
The MINIMUM temperature required for a substance to initiate self-sustained combustion is the |
ignition temperature |
|
The danger from static electricity is highest during |
cold, dry weather |
|
All of these have the potential for serious injury, when wearing jewelry EXCEPT |
wearing gloves on the hand to prevent injury |
|
Which personnel protective equipment is not normally used in the nondestructive inspection process? |
Long sleeves |
|
Unattended parked vehicles on the flightline must |
have keys left in the ignition |
|
Engine position numbers on multi-engine aircraft are assigned consecutively from the |
tip of the left wing to the tip of the right wing |
|
Where is am aircraft elevator located? |
On the empennage |
|
The tie-down rings on aerospace ground equipment (AGE) are normally attached to the |
frame |
|
Areospace ground equipment (AGE) power system components are NOT made from |
copper |
|
How are permanent joints on Areospace ground equipment (AGE) enclosures normally attached? |
Riveted |
|
How many standard markings are applied to all Air Force aircraft? |
Six |
|
Where are station numbers located on fixed wing aircraft? |
Nose |
|
Which is NOT an aircraft identification and safety marking? |
Crew |
|
What symbol is used to indicate an installed ejection system? |
Triangle with apex pointed down |
|
What small and subdued safety marking alerts you to a hazardous condition? |
Warning text |
|
Depending on the type of aircraft and engine, how big is the noise safety zone circle surrounding the airflcraft? |
300 to 400 feet |